avdel拆卸鉚釘槍

avdel有一款可以拆卸鉚釘的鉚釘槍，它只能拆除環槽鉚釘，但不能拆除密封塞、抽芯鉚釘、鉚螺母及快速鉚釘。

可以使用avdel的抽芯鉚釘槍nG4和73200環槽鉚釘槍做為基本工具，再配上不同尺寸的拆卸槍頭即可。

此工具的安全條款如下：

1 Do not use collar cropper outside the design intent printed below.
2 Do not use equipment or tools with this collar cropper other than that recommended and supplied by Avdel UK Limited.
3 The tool and collar cropper must be maintained in a safe working condition at all times. The operator must follow the daily and weekly
service checks detailed in the Genesis® G4, nG4 or G2LB Instruction Manual.
4 The tool and collar cropper shall at all times be operated in accordance with the relevant health and safety legislation. Any question
regarding the correct operation of the tool and operator safety should be directed to your local Avdel company or authorized
representative.
5 Do not operate a tool that is pointed towards any person(s).
6 Do not operate the tool if it is not fitted with a complete collar cropper assembly.
7 FINGERS AND ALL BODY PARTS MUST REMAIN CLEAR OF THE COLLAR CROPPER WHEN OPERATING THE TOOL.
8 When using the tool and collar cropper, the wearing of safety glasses is required both by the operator and others in the vicinity to protect
against ejection of debris. We recommend wearing gloves if there are sharp edges or corners on the application.
9 Take care to avoid entanglement of loose clothes, ties, long hair, cleaning rags etc., in the moving parts of the tool and collar cropper.
10 When carrying the tool from place to place keep hands away from the trigger to avoid inadvertent start up.
11 THE AIR SUPPLY MUST BE DISCONNECTED WHEN FITTING OR REMOVING ANY NOSE ASSEMBLY.

 

拆卸槍頭分解圖片如下：

 

 

71230-20100 3/16 COLLAR CROPPER KIT - AVDELOK®/ MAXLOK®
71230-20110 1/4 COLLAR CROPPER KIT - AVDELOK®
71230-20120 1/4 COLLAR CROPPER KIT - MAXLOK®
1* 07500-06800 Collar Cropper Assembly 3/16 Avdelok®/Maxlok®
1* 07500-06900 Collar Cropper Assembly 1/4 Avdelok®
1* 07500-05900 Collar Cropper Assembly 1/4 Maxlok®
2 07498-05001 Anvil Adaptor
3 07498-05002 Collet Adaptor
4 71210-02101 Jaw Spreader Housing
5 07003-00277 ‘O’ Ring
6 71233-20300 Stop Nut Assembly - Collar Cropper
7 71210-20201 Safety Cap
8 71213-20201 Safety Cap - Quick Release Bottle
9 07900-00828 Collar Cropper Data Sheet
07900-00828

 

 

拆卸槍頭不同于鉚釘槍、快速鉚釘槍或是鉚螺母槍，需要專業的安裝人員進行安裝調試，具體步驟如下：

To prepare base tools to accept Collar Cropper equipment
1 Unscrew Jaw Spreader Housing 71210-02101, (Chuck Collet Adaptor 07610-00501 for G2LB). Remove Locknut 71210-02105 and Seal Housing 71210-02104. Remove VacuumSleeve 71230-02102 (applies to G4 and nG4 only).
2 Screw Stop Nut 6 fully onto the Piston by hand. Refit Jaw Spreader Housing 71210-02101, ((4 and 5) supplied in kitfor G2LB), screw fully onto the Piston before tightening StopNut 6 against it.
3 Remove the Stem Collector Bottle Assembly and replace with Safety Cap 7. For nG4 tools fitted with Quick Release Collector Bottles remove and fit Safety Cap 8.
Fitting the Collar Cropper Assembly
1 Screw Collet Adaptor 3 onto Jaw Spreader Housing 4 and 5 and tighten.
2 Screw Anvil Adaptor 2 over the Collet Adaptor 3 into the front of the tool and tighten.
3 Attach Cropper Assembly 1* by screwing the Cam Rod of the Assembly onto the Collet Adaptor 3.
4 Complete attachment by screwing the Nose Retaining Nut of the Collar Cropper 1* assembly onto the Anvil Adaptor 2.